Skip to content
Shop
Explore

INDEPENDENT BMW ENGINE EXPERTISE

Re-adaptation of the engine using ISTA D/+

N43 / N53 · NOXEM · DIAGNOSTICS

Select a technical image to view it in detail.

This procedure resets the engine adaptation values in ISTA D/+ and then rebuilds them. After the reset, the flywheel adaptation and the fuel mixture re-adaptation are performed by driving, followed by a few cold-start and longer drive cycles. Troubleshooting notes are at the end.

Resetting the adaptations in ISTA D/+

1. Start a new session in ISTA D/+, then identify the vehicle and run a test.

2. Open the menu Vehicle management.

3. Open the menu Service function.

4. Open the sub-menu Power train and press Start search.

5. Open the sub-menu Engine Electronics.

6. Open the sub-menu Adjustment functions.

7. Select Delete adaptations/variants.

8. Select Delete engine adaptation value and press Display.

9. Select Reset adaptation values and versions (encoding).

Follow the instructions on the screen.

Important: Follow the instructions very carefully. If the reset succeeded, you will see the notice “Adaptation values and taught versions were reset”. If ISTA D/+ does not display this notice after the attempt, repeat the procedure.

Step 10: Flywheel adaptation

1. Start the engine.

Attention: the car may run unevenly. If the EML (check engine) symbol appears on the KOMBI and the idle is increased or incorrect:

  • Turn off the engine and turn on the ignition.
  • Slowly press and release the accelerator pedal three times.
  • Start the engine.

2. On a level road, accelerate to 100–110 km/h. 3. Select 4th gear (on an automatic transmission, use manual mode). 4. Release the accelerator pedal and let the engine brake the car for 7–10 seconds, without pressing the brake pedal. 5. Repeat steps 2–4 three times in total. 6. Stop the car, switch off the ignition, remove the key and disconnect the diagnostics cable. 7. Wait until the lighting of the Start/Stop button turns off.

Step 11: Fuel mixture re-adaptation

1. Start the engine.

Attention: the car may run unevenly. If the EML (check engine) symbol appears on the KOMBI and the idle is increased or incorrect:

  • Turn off the engine and turn on the ignition.
  • Slowly press and release the accelerator pedal three times.
  • Start the engine.

2. Let the engine idle for 5 minutes. 3. Drive at an even speed of 60–90 km/h for 5–10 minutes. 4. Repeat steps 2–3 several times. 5. Stop the car, switch off the ignition, remove the key and disconnect the diagnostics cable. 6. Wait until the lighting of the Start/Stop button turns off.

Recheck the fault memory and clear it if necessary.

Step 12: Following cold starts

For the next few cold starts:

1. Let the engine idle for at least 5 minutes. 2. Drive longer sessions with even RPM and torque where possible.

With this, the creation of the initial adaptations can be considered complete.

Fault messages to expect

Note: immediately after the adaptations are cleared, the following fault messages* can appear:

  • Faults relating to DSC. Solution: drive for 10–15 minutes, then switch the ignition off and on.
  • Faults relating to the throttle. Solution: turn on the ignition, press and release the accelerator pedal three times, then start the engine.

While the new adaptations are being learned, these fault messages* can appear:

  • Fuel trim (bank and/or individual cylinders)
  • Insufficient performance of the CO catalytic converters
  • Lambda probes (trim and/or signal)
  • Uneven running (stratified charge and/or homogeneous injection)

*In this situation, these messages do not indicate any problem with engine performance.

Once the new adaptations are complete (after 5–8 driving sessions with a cold or warm engine, at least 200–300 km), check them and, if necessary, clear the fault memory with INPA or ISTA D/+.

Troubleshooting

1. At the start of an ISTA D/+ session the vehicle’s basic data does not appear and has to be entered manually. The menus for the NOx sensor and NOx converter are not accessible. The cause is a communication problem between ISTA D/+ and the car. Typical culprits are the OBD/USB host or the ICOM IP address and port settings. Contact the interface vendor to resolve the issue. Once communication is established, the car’s basic data is read from the car.

2. After you confirm the reset (by pressing “Continue” at the warning “Adaptation values will now be reset”), the message “Could NOT reset adaptation values” appears. The condition “Ignition ON” is not met. See item 3.

3. How do I achieve “Ignition ON” if my car has no ignition key and uses a Start/Stop button?

  • Insert the key into the slot.
  • Do not press any pedal (neither clutch nor brake).
  • Press the Start/Stop button several times until all the indicators (ABS/DTC, SRS, etc.) light up in the KOMBI.

4. After you confirm the reset (by pressing “Continue” at the warning “Adaptation values will now be reset”), the message “Switch off Terminal 15 and terminal R” appears.

  • Switch off the ignition.
  • Remove the key from the slot.
  • Wait for further instructions.

BEYOND THE FAULT CODE

A clearer picture.
A better next step.

Get in touch
Enlarged technical image
Open original image