Skip to content
Shop
Explore

INDEPENDENT BMW ENGINE EXPERTISE

Required information for F series

N43 / N53 · NOXEM · DIAGNOSTICS

Below is the information and diagnostic data we need to assess a BMW 523i/525i/530i engine problem. Please send it as described.

Note: INPA for F series and MSD87 loader 3.700 are required.

Basic information about the car

Please send us:

  • the model: 523i, 525i or 530i
  • the mileage
  • a short description of the problem

Preparing the car

1. Warm up the engine to working temperature, at least 90 °C (see the temperature note at the end). You can monitor it in INPA at ../F5/F1/F2. 2. Drive at least a few kilometres at a speed of at least 20 km/h. 3. Stop the car without switching off the engine, and take the screenshots below at idle.

Screenshots at idle

For every menu marked “scroll down”, scroll to the end of the list or menu before taking the screenshot.

  • ../F4/F1: errors, Main list (scroll down to the end of the list)
  • ../F4/F3: errors, History list (scroll down to the end of the list)
  • ../F5/F4: VANOS
  • ../F5/F5/F2: IBS/Battery data
  • ../F5/F5/F3: IBS/Battery data
  • ../F5/F1/F1: basic engine parameters (scroll down to the end of the menu)
  • ../F5/F1/F2: basic engine parameters (scroll down to the end of the menu)
  • ../F5/F1/Shift+F1: oil sensor
  • ../F5/F6: fuel mixture (scroll down to the end of the menu)
  • ../F5/F7: rough run menu
  • ../F5/F9: injector live data at idle (scroll down to the end of the menu)
  • ../F5/Shift+F3: injector tests at partial load (scroll down to the end of the menu)
  • ../F6/F2/F5: NOx converter menu

Screenshots after restarting the engine

Switch the engine off, then start it again and wait at least 30 seconds without pressing the accelerator pedal (this guarantees Homogeneous injection mode). Then take these screenshots:

  • ../F5/F6: fuel mixture (scroll down to the end of the menu)
  • ../F5/F7: rough run menu
  • ../F5/F9: injector live data at idle (scroll down to the end of the menu)

Cold-start video

Please also send a video of a cold start:

1. Connect INPA, turn the ignition on and open ../F5/F1/F2 (basic engine parameters). 2. Start the engine. 3. Open ../F5/F6 (fuel mixture) for 3 to 5 seconds. 4. Open ../F5/F7 (rough run data) for 3 to 5 seconds. 5. Open ../F5/F9 (injector data) for 3 to 5 seconds, scrolling down to the end of the menu. 6. Repeat steps 3 to 5 five to ten times.

If the DME seems to disconnect cylinders

If you suspect that the DME permanently switches off some of the cylinders:

1. Turn the engine off. 2. Start the engine again, and repeat this.

Each time the engine is restarted, the DME tries to enable all cylinders. Keep recording the Fuel mixture and Rough run data menus during these restarts. If the DME switches off any cylinder, restart the engine again after some time. The recorded video must be at least 2 to 3 minutes long.

Engine temperature reference

The engine temperature reference is shown here:

[[[KEEP1]]](https://bimmerprofs.com/wp-content/uploads/2019/08/engine_temperature_F_series.png)

BEYOND THE FAULT CODE

A clearer picture.
A better next step.

Get in touch
Enlarged technical image
Open original image