Skip to content
Shop
Explore

INDEPENDENT BMW ENGINE EXPERTISE

Unsuccessful desulphation

N43 / N53 · NOXEM · DIAGNOSTICS

Select a technical image to view it in detail.

The N43/N53 engines have a specific need: from time to time the NOx catalytic converter has to be cleaned of sulfur. Even the cleanest petrol contains some sulfur, which deposits on the walls of the catalytic converter, reduces its performance and damages it. The cleaning intervals range from several thousand km for a new converter to 500 to 1000 km for a used one.

If desulfation is not possible for some reason and the converter becomes too contaminated, the DME stores fault 30EA. The engine then no longer runs in stratified charge mode and has trouble creating adaptations. After a while vibration and misfires start, and starting becomes difficult. Fuel consumption rises, and the exhaust emissions are so poor that the car cannot pass the TI. Some people replace injectors and high-pressure pumps, without success.

The patient

The car is a BMW 1 Series, E81.

The only fault stored is 30EA: the NOx catalytic converter is contaminated. What to do in this case? With INPA or ISTA D, activate the converter cleaning session and drive at 110+ km/h for at least half an hour. During the drive, monitor the exhaust temperature (it will rise to 600 °C) and Lambda (it will drop to 0.95).

The NOx sensor is dead

I activated the desulfation session and prepared to clean the converter. Before starting, I ran one more test: checking that the NOx sensor works.

Although all the necessary conditions were met (engine and exhaust temperature, minimum driving time and speed, and so on), the sensor sent no data:

The incorrect values are marked in red. They show that the sensor has not switched on and is not Online, so it is damaged. This is unfortunately a very common defect. Even more unpleasant, no fault is stored in the DME fault memory. With a damaged sensor, the engine will not allow the converter to be cleaned, and stratified charge is switched off. The engine suffers all the problems typical of a damaged NOx system.

After removing the sensor, another unpleasant surprise followed: the OEM sensor is very old, release 02.

The current release (from the last 4 to 5 years) is 05, so this sensor is at least 7 to 8 years old. These sensors do not last that long. It is clear the sensor had been damaged for a long time, and for just as long the NOx catalytic converter had not been regenerated and cleaned. So even though the mileage is low, the expensive NOx catalytic converter is certainly damaged.

Repair options

The owner had two options:

  • Replace the complete NOx system (catalytic converter and sensor), at a repair cost of around EUR 2500.
  • Install the NOXEM.

He chose the NOXEM.

Coding and re-adaptation

After installing the NOXEM, certain service procedures have to be performed. The picture shows the coding process.

This is what the NOXEM data looks like in homogeneous mode. Both Lambda values (wideband and narrowband) are reported, along with the NOx content:

Next comes the re-adaptation of the engine, starting with the flywheel and its sensor:

The fuel mixture adaptations for all modes follow. After long years, the engine again runs in the fuel-saving stratified charge mode. At 100 km/h, fuel consumption is 4.3 l/100 km!

The NOXEM also confirms stratified charge, with Lambda 2.24:

Results: injectors and idle quality

After a break of several years, the engine resumed its injector measurements. The correction for cylinder No. 4 (by position) is marked in red: this injector is slightly leaking.

Finally, a few images showing how the engine runs as the manufacturer intended.

Idle smoothness in stratified charge: all bars are practically 0.

Such data means the mechanical efficiency of the cylinders is perfectly even. Sitting in the car, we did not even feel that the engine was running.

Here is the idle in homogeneous mode. The contribution of cylinder No. 4 differs by several %: it is increased, because the injector delivers a slightly larger amount of fuel. It will take several days until the DME has fully compensated for the leaking injector.

This slight difference in efficiency cannot be felt, and the engine seems to run perfectly with no vibration. But the Siemens engine management detects it and will correct for it. All this functionality works only if all the engine’s systems are in order, including the NOx system.

Final checks

After the required re-adaptations I ran a short test. All the necessary adaptation learn bits are colored, so the adaptations completed successfully.

The engine temperature corresponds to high power mode. LPFP and HPFP pressures are correct, and the Nernst resistances of both Lambda probes are correct. Everything is in order.

After some time, the behavior of injector No. 4 should be checked again. If the leak does not get worse, there is no need to replace the injector, because the DME takes this parameter difference into account and compensates for it. If the leak increases significantly, the injector will have to be replaced or cleaned.

P.S. Spark plugs

The repair of this engine started with replacing the spark plugs. The reason: cylinder No. 4 stubbornly refused to work, and the history memory contained misfire faults for all cylinders. The owner admitted that new spark plugs had been installed recently. They were good, not cheap ones: Bosch.

I remind you again: only NGK manufactures the spark plugs for these engines!

The image shows how significantly NGK (right) and Bosch (left) differ.

BEYOND THE FAULT CODE

A clearer picture.
A better next step.

Get in touch
Enlarged technical image
Open original image