Skip to content
Shop
Explore

INDEPENDENT BMW ENGINE EXPERTISE

E series. N43/N53 operation modes. Stratified charge performance check

N43 / N53 · NOXEM · DIAGNOSTICS

Unfortunately, none of the available diagnostic programs shows clearly which modes are allowed: Homogeneous only, Homogeneous plus Homogeneous lean, or all modes including Stratified charge. We therefore have to rely on several indirect indicators and parameters. This article walks through them for the N43/N53 with the MSD80, from reading the mode in INPA to judging the condition of the NOx catalytic converter.

Reading the operating mode in INPA

A first indication of the mode the engine (N43/N53) is running in is available in INPA: system diagnosis, EOL operation mode switching section (../F9/F1).

[[[KEEP1]]](https://bimmerprofs.com/wp-content/uploads/2017/06/BMW_ISTA_operation_mode_1.png)

Sample: engine operating in Homogeneous mode.

INPA shows which mode the engine is in at the moment:

  • Homogeneous (left)
  • Homogeneous lean (Lambda ~1.5)
  • Stratified charge (Lambda 1.8 .. 3.5)

Remark: forced switching to Homogeneous and Homogeneous lean is possible at idle (Homogeneous lean only if Stratified charge is allowed). If Stratified charge is allowed, then on several MSD80 releases (under specific conditions) it will activate after pressing F3 once the engine runs above 1000 .. 1200 RPM.

[[[KEEP2]]](https://bimmerprofs.com/wp-content/uploads/2017/06/BMW_ISTA_operation_mode_2.png)

Sample: engine running in Stratified charge with Lambda ~2.0.

Fault codes that block Stratified charge and Homogeneous lean

First of all: if the engine control unit memory contains fault codes related to the NOx catalytic converter and/or the NOx sensor, the most advanced modes, Stratified charge and Homogeneous lean, will not be available. The engine then runs in the alternative (emergency) mode, Homogeneous injection.

Fault codes that prevent Stratified charge and Homogeneous lean:

  • 2AF0, 2B05: NOx sensor, heating
  • 2AF2, 2B06, 2B09: NOx sensor, Lambda linear
  • 2AF4, 2B07, 2B0A: NOx sensor, electrical
  • 2AF6, 2AFB, 2B0B: NOx sensor, Lambda binary
  • 2AF8, 2AF9: NOx sensor, NOx signal: coast mode check
  • 2EAE: NOx sensor message missing (timeout)
  • 30D6: NOx sensor, plausibility
  • 30D8: NOx sensor, sensor damaged
  • 30DA: NOx sensor, heating time
  • 30DC: NOx sensor, heating
  • 30DE: NOx sensor, Lambda probe before catalytic converter, correlation
  • 30E0: NOx sensor, offset
  • 30E2: NOx sensor, thrust test
  • 30E4: NOx sensor, aging
  • 30E6: NOx sensor, dynamics
  • 30EA: NOx catalytic converter, sulphurized
  • 30E9: NOx catalytic converter, aging

Of course, other significant faults (relating to Lambda sensors, VANOS, etc.) also disable Stratified charge.

If none of these codes is present, there is a good chance the N43/N53 will perform as it should.

Test procedure

To find out whether the engine works in all the modes it should:

  • Heat it up to operating temperature (95 .. 105 °C).
  • Start driving at no less than 20 km/h.
  • Heat the exhaust system to at least 220 °C.
  • Check that the NOx sensor switches on and starts transmitting data.
  • Continue driving at 70 .. 90 km/h with steady speed and load, and check whether the engine switches to Stratified charge.
  • If Stratified charge is active, check the condition (efficiency) of the NOx catalytic converter.

The sections below describe each step.

Engine and exhaust temperature

Engine temperature. I don’t think warming up needs special instructions. I would only note that you should not do it too aggressively or dynamically. MSD80 can react by switching to its “sports” mode, which turns Stratified charge off for a while.

To check the engine temperature:

  • Open INPA, section MSD80 for N43/N53.
  • Open the analog modules menu with F5.
  • Open the analog data submenu with F2, then press F6.

[[[KEEP3]]](https://bimmerprofs.com/wp-content/uploads/2017/08/N53_engine_temperature.png)

Vehicle speed. There is no limitation: you can drive as slowly or as fast as necessary, and even stop for a while. The main conditions are that the exhaust is hot (220 °C) and the speed is above 20 km/h, at least for some time.

Exhaust temperature. To check it:

  • Open INPA, section MSD80 for N43/N53.
  • Open the analog modules menu with F5.
  • Open the NOx sensor submenu with Shift + F2.

The exhaust temperature sensor reading is shown in the right corner:

[[[KEEP4]]](https://bimmerprofs.com/wp-content/uploads/2017/06/BMW_INPA_NOx_menu_1.jpg)

The indicator on the right shows the temperature in °C. For the NOx sensor to switch on, the temperature has to reach 220 °C and the vehicle speed has to be at least 20 km/h.

Checking that the NOx sensor is online

To see whether the NOx sensor has switched on, open the sensor menu (../F5/Shift+F2, as above). The NOx concentration is shown at the top left:

[[[KEEP5]]](https://bimmerprofs.com/wp-content/uploads/2017/06/BMW_INPA_NOx_menu_2.jpg)

  • 0 ppm: the sensor is either off, or on but not sending data for some reason.
  • Any value other than 0 ppm: the sensor is on and sending actual data.

A working sensor switches on and starts transmitting data about 2 minutes after these conditions are met:

  • the engine is warmed up;
  • the exhaust temperature is at least 220 °C;
  • the vehicle speed is at least 20 km/h.

Unfortunately, “surprises” can happen even at this stage. The NOx sensors are supplied by Continental, which has gone through several hardware generations and even more software releases. Still, ALL the software releases I tested had one feature in common: as the sensor ages (above 50,000 .. 80,000 km), it has trouble switching on and entering its working mode. The technical problem is an increased reaction time and endless current oscillation in the sensor’s chemical cells (oxygen and NOx), so the control electronics cannot reach a stable working condition. Typically the sensor tries to switch on (it starts heating) and sends a “not ready” status to MSD80. MSD80 does not log any fault; it simply waits for the sensor to start working, for a very long time.

If you see this situation, the sensor is damaged and has to be replaced. The signs are that the NOx indicator keeps showing 0 ppm for a long time while the exhaust temperature values keep changing, which proves that INPA is connected to MSD80.

Checking Stratified charge

If the NOx sensor transmits actual data (NOx values other than 0), it is time to check whether Stratified charge switches on. This is the most important and also the most complicated operating mode of the N43/N53.

Stratified charge can be seen in two menus:

  • the exhaust (adaptations) menu, /F5/F6;
  • the NOx sensor menu, /F5/Shift + F2.

In both menus you check the Lambda values. The exhaust menu shows the wide-band Lambda values for both banks (before the catalytic converter). The NOx sensor menu shows the wide-band Lambda value reported by the sensor (second line on the right side of the menu).

NOx sensor menu:

[[[KEEP6]]](https://bimmerprofs.com/wp-content/uploads/2017/06/BMW_INPA_NOx_menu_3.jpg)

Exhaust menu (adaptations):

[[[KEEP7]]](https://bimmerprofs.com/wp-content/uploads/2017/06/BMW_INPA_adaptations_menu_1.png)

Accelerate to 70 .. 90 km/h, switch on the cruise control and follow the Lambda values. Within a few minutes (almost immediately, if the engine has no fault codes) Lambda should rise above 1.4.

If it does not, the behavior points to one of these causes:

  • Lambda stubbornly stays around 1.0. Very dynamic driving beforehand may have caused MSD80 to switch Stratified charge off. If so, stop for 2 .. 3 minutes, accelerate normally to 70 .. 90 km/h and continue to observe the Lambda values.
  • Lambda stays around 1.4 .. 1.6. The control unit has detected real uneven running in Stratified charge (you cannot miss it, you will feel twitching) or fake uneven running (described here), and/or insufficient efficiency of the catalytic converters. You should very soon see the corresponding fault code:
  • 3104: uneven running, stratified charge operation
  • or 29F4, 29F5, 2A26, 2A27, which relate to the catalytic converters (more information here).

The cause of the uneven running has to be eliminated, but only if you really feel the engine twitching. If there is no real problem (no twitching etc.), the fault can be caused by an uneven road, as described here.

  • High NOx values. If the NOx content in the exhaust reaches several hundred ppm right from the start of driving, there is a problem. If the following code is not stored:
  • 30E9: NOx catalytic converter, aging

it will very likely appear soon, or it is “masked”: tuners have deleted it from the MSD80 fault map. There is no fault code, but the engine does not perform as it should. In this case, check the software release in MSD80. If it does not match the one offered by the manufacturer, it has to be restored. The existing (most probably tuned) version can be stored as a copy and reinstalled once the engine problems are solved.

If the engine has no operational problems, Lambda should exceed 2.2. If Lambda reaches 2.6 .. 3.2 at 70 .. 90 km/h, congratulations: the engine is running in Stratified charge.

If Lambda reaches only 1.4 .. 1.6, then, as described above, Stratified charge is allowed but the control unit has detected some unevenness (possibly a misfire in one of the cylinders) or reduced NOx catalytic converter performance, and the engine has switched to Homogeneous lean. The operating range of this mode is extended (for a while) to the area of medium loads.

A Lambda reduction caused by real (not falsely detected) misfires is not a critical fault, since after some moments MSD80 will try to raise Lambda again to a maximum of 2.6 .. 3.2. It should still be fixed, because excess fuel in the exhaust system damages the catalytic converters.

Evaluating NOx catalytic converter performance

If Lambda reaches 2.6 .. 3.2, the last stage of the test is the evaluation of catalytic converter performance.

Use a stopwatch to record how long Lambda stays above 1.4. After some time (10 .. 60 seconds) Lambda drops below 1.0 for several seconds. During this period MSD80 performs regeneration (cleaning) of the NOx catalytic converter. Measure several consecutive cycles (at least 3) and take the longest as the result. It indicates the condition of the NOx catalytic converter:

  • 30 .. 60 seconds. An unbelievably perfect result. Unless the NOx catalytic converter has been replaced recently (within the last 10,000 .. 20,000 km), such a result is not possible.
  • 20 .. 30 seconds. Congratulations, the NOx catalytic converter is in working condition. Going forward, use high-quality low-sulfur fuel and keep all engine systems in order, and you will enjoy the N43/N53 for a long time.
  • 10 .. 15 seconds. This is the minimum time for a Stratified charge cycle. It means the NOx catalytic converter cannot cope with the accumulation of nitrates. If fault 30E9 is not present yet, you will soon see it. You can try forced regeneration of the catalytic converter using the ISTA D service functions, but don’t be too optimistic that it will improve the situation.

Note: if you see shorter Stratified charge cycles between the longer ones, or longer periods (up to a minute) with Lambda at 1.0, there is no need to worry. MSD80 regularly calibrates the wide-band probes of each bank, calibrates the Lambda values for the NOx sensor and its reference level, and performs individual Lambda corrections for each cylinder and each bank. During calibration Lambda varies between 0.97 and 1.03. MSD80 also regularly checks the EGR and other systems, and Stratified charge is likewise stopped for a while at those moments.

Related entries

Rough run. Trim errors. Hidden cause

N43/N53 operation modes. Basics

Performance check of NOx sensor

Direct injection. Stratified charge

NOx catalytic converter regeneration and desulfation

FAQ about NOx emulator

BEYOND THE FAULT CODE

A clearer picture.
A better next step.

Get in touch
Enlarged technical image
Open original image